Using Eddy-Current Sensors for Thread Detection

Copyright © 2015 Lion Precision. www.lionprecision.com

Summary

This Application Note describes the use and setup of special thread detecting probes with standard Lion Precision eddy-current sensor electronics. Different electronics are required for ferrous versus nonferrous materials.

Introduction

Specially designed thread-sensing probes can be used with standard eddy-current sensor electronics to detect the presence/absence of threads in a hole. Thread sensors generate different output voltages for tapped versus untapped holes. 
The ECA101 is used for ferrous materials and can create a voltage difference of 3-4 volts between tapped and untapped holes. The ECL101 is used for nonferrous materials and creates a 1.0 volt difference between tapped and untapped holes.

Basic Theory of Operation

Eddy-Current probes are primarily designed as displacement sensors measuring changes of the gap between the sensor and the target. Specially designed thread-dection probes have longer probe-tip extensions which allow for deeper hole penetration and for the magnetic field of the sensing coil to engage the sides of the hole being tested.

The fundamental principle is that an untapped hole’s surfaces are, on average, “closer” to the probe than a tapped hole’s surfaces. This change in average distance from the probe to the surrounding material creates a change in output voltage from the electronics.

Material Differences

Ferrous Materials (Steel)

Thread sensing in ferrous materials is accomplished with a thread sensing probe and ECA101 driver electronics. The output voltage differences between tapped and untapped holes is substantial as shown below in the charts of typical output voltages.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nonferrous Materials (Aluminum)

Thread sensing in nonferrous materials is accomplished with a thread sensing probe and ECL101 driver electronics. The output voltage differences between tapped and untapped holes are much less than with ferrous materials. This has proven to work reliably but greater consideration must be given to the application as the margin for error is smaller. The charts below show typical output voltages for nonferrous applications.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Selecting a Probe and Driver Electronics

Driver Electronics

The ECA101 used with ferrous materials offers an analog output voltage and a setpoint switched output. The switched output can be used to create a Go/NoGo type indication for thread detection. 
The ECL101 used with nonferrous materials has an analog output only which will have to be evaluated by a data acquisition system to determine the presence/absence of threads.
Each driver model manual has a “Thread Sensing” addendum with instructions on how to best setup the sensor for sensing threads.

Thread Sensing Probes

Probe selection is dependent on material type and hole/thread type. Ferrous materials (steel) use the ECA101 Driver; nonferrous materials (aluminum) use the ECL101 Driver.
Select the probe from the tables below:

Ferrous Materials Metric Inch Probe M6 x 1 1/4-20 T5BZ M7 x 1 1/4-28 T5BZ M8 x 1 M8 x 1.25 5/16-18 5/16-24 T6BZ M10 x 1.25 M10 1.5 3/8-16 3/8-24 T7BZ M12 x 1.25 M12 x 1.75 7/16-20 1/2-13 T8BZ M14 x 1.5 M14 x 2 9/16-12 9/16-18 T10BZ M16 x 1.5 M16 x 2 5/8-11 5/8-18 T12BZ Use: ECA101 Eddy-Current sensor

Nonferrous Materials Metric Inch Probe M5x0.8 – T5BZ M6x1 1/4 – 20 1/4 – 28 T6BZ M7x1 5/16 – 18 T7BZ M8x1 M8x1.25 5/16 – 24 T8BZ M10x1.25 M10x1.5 3/8 – 16 3/8 – 24 T10BZ M12x1.25 M12x1.75 7/16 – 20 1/2 – 13 T12BZ M16x1.5 M16x2.0 – T16BZ Use: ECL101 Eddy-Current sensor

 

Mechanical and Mounting Considerations

Centering

The output voltage will change if the probe is not perfectly centered in the hole. The change is not large, but especially for nonferrous materials with smaller margin of error, this should be considered when using the probes. Complete details are available in the “Thread Sensing Probe Centering Errors” TechNote LT02-0015.

Protecting the Probe

Severe centering errors or other mishaps may cause the probe to crash into the target. Nonferrous sensor diameters are about 85% of the hole size, while ferrous sensors are about 65% of the hole size. The table below shows typical gap sizes:

Ferrous Materials Hole Size Probe Gap (inch/mm) M6 x 1 T5BZ 0.035/0.88 M7 x 1 T5BZ 0.054/1.37 M8 x 1.25 T6BZ 0.052/1.31 M8 x 1 T6BZ 0.057/1.45 M10 x 1.5 T7BZ 0.065/1.65 M10 x 1.25 T7BZ 0.071/1.80 M12 x 1.75 T8BZ 0.087/2.21 M12 x 1.25 T8BZ 0.096/2.44 M14 x 2 T10BZ 0.088/2.24 M14 x 1.5 T10BZ 0.098/2.49 M16 x 2 T12BZ 0.092/2.33 M16 x 1.5 T12BZ 0.101/2.58

Nonferrous Materials Hole Size Probe Gap (inch/mm) M5 x .8 T5BZ 0.018/0.46 M6 x 1 T6BZ 0.018/0.46 M7 x 1 T7BZ 0.018/0.46 M8 x 1.25 T8BZ 0.018/0.46 M8 x 1 T8BZ 0.024/0.60 M10 x 1.5 T10BZ 0.018/0.46 M10 x 1.25 T10BZ 0.024/0.61 M12 x 1.75 T12BZ 0.018/0.46 M12 x 1.25 T12BZ 0.027/0.68 M16 x 1.5 T16BZ 0.018/0.46 M16 x 2 T16BZ 0.028/0.71

 

Spring-loaded probe mounts can be used to protect probes from damage in case of crash. Three models are available for different probe sizes:

	Model Number
	SN-08	SN-12	SN-18
Internal Thread (must match probe)	M8x1 (T5-8)	M12x1 (T10-12)	M18x1 (T16)
External Thread	M16x1.5	M22x1.5	M30x1.5
Maximum Extension	0.35″ (8.9mm)	0.41″ (10.4mm)	0.49″ (12.4mm)

 

Thread Sensing Probe Dimensions

 

 

 

 

Mechanical Specifications
Probe	Dimension “A”	Body Thread
T5BZ	0.13″ / 3.3mm	M8x1
T6BZ	0.16″ / 4.1mm
T7BZ	0.20″ / 5.1mm
T8BZ	0.23″ / 5.8mm
T10BZ	0.30″ / 7.5mm	M12x1
T12BZ	0.37″ / 9.3mm
T16BZ	0.52″ / 13.1mm	M18x1